Search found 4574 matches

by Charles uk
Wed Jun 12, 2019 7:39 pm
Forum: General Topics
Topic: New Baby
Replies: 13
Views: 380

Re: New Baby

You should have asked Rene, We had some Birmabright mixed so remanufactured parts are the same colour, not cheap, but we're all a bit anal!

Quite a few people have said that about me!
by Charles uk
Wed Jun 12, 2019 6:00 pm
Forum: General Topics
Topic: Long distance Seagull trip.
Replies: 5
Views: 179

Re: Long distance Seagull trip.

42 miles around the island of Bermuda.

I'm not sure how far the Waikato race is, 80 something miles.

Search for the trip on the Murry the Aussies did.
by Charles uk
Mon Jun 10, 2019 6:33 pm
Forum: Help
Topic: Plug gap
Replies: 11
Views: 297

Re: Plug gap

Undo the 1/4" BSF bolts below the baseplate, these should release the flywheel cover & with luck you should be able to lift it enough to see the bottom 1/2" of the flywheel rim & be able to see a shallow groove 3/8" above the bottom of the flywheel base, if the groove is prese...
by Charles uk
Mon Jun 10, 2019 1:25 pm
Forum: Help
Topic: Plug gap
Replies: 11
Views: 297

Re: Plug gap

Sorry getting you mixed up with another Seagull can't say anything about yours, as we don't have the engine number.
by Charles uk
Mon Jun 10, 2019 9:57 am
Forum: Help
Topic: Plug gap
Replies: 11
Views: 297

Re: Plug gap

Yours is a factory rebuild & that doesn't tell us which ignition they fitted.

Remove flywheel cover & inspect flywheel rim,

no groove white CDI

groove black CDI

Run at 25 thou until your sure, as the black CDI struggles at 35 thou, & replacements are expensive!
by Charles uk
Mon Jun 10, 2019 8:21 am
Forum: Help
Topic: Plug gap
Replies: 11
Views: 297

Re: Plug gap

Well the White CDI is 35 thou & the Black 25.

I run both at 25 thou & haven't had a problem yet.
by Charles uk
Mon Jun 10, 2019 12:33 am
Forum: Help
Topic: Plug gap
Replies: 11
Views: 297

Re: Plug gap

It's dependent on which type of ignition you have fitted to your model 90, black or white CDI.

A picture of the flywheel rim will tell us.
by Charles uk
Sun Jun 09, 2019 10:25 pm
Forum: Help
Topic: TC 102 water cooling problem
Replies: 23
Views: 961

Re: TC 102 water cooling problem

Dependent on engine number.
by Charles uk
Sun Jun 09, 2019 10:38 am
Forum: For Sale
Topic: Curlew
Replies: 4
Views: 518

Re: Curlew

Depends whether you want it as an ornament or as an outboard motor?

It drives the same prop / lower unit combination as a silver century model 75 at a 1000+ rpm faster, uses less fuel & makes less noise, & has about 30% more oomph!
by Charles uk
Thu Jun 06, 2019 9:36 pm
Forum: Help
Topic: TC 102 water cooling problem
Replies: 23
Views: 961

Re: TC 102 water cooling problem

Oil there is usually from a worn pinion bearing.
by Charles uk
Wed Jun 05, 2019 5:18 pm
Forum: General Topics
Topic: Silver Century not starting
Replies: 18
Views: 1605

Re: Silver Century not starting

That's a very big increase for just a hone, new rings & an early head or did you skim the top off the cylinder?
by Charles uk
Wed Jun 05, 2019 1:36 pm
Forum: General Topics
Topic: Silver Century not starting
Replies: 18
Views: 1605

Re: Silver Century not starting

What was the compression difference between before & after?
by Charles uk
Sun Jun 02, 2019 7:29 pm
Forum: Help
Topic: TC 102 water cooling problem
Replies: 23
Views: 961

Re: TC 102 water cooling problem

Can someone post a picture of the telltale block on the side of an 102 exhaust tube so Red can see where all 102's feed water back into the exhaust, perhaps a previous owner has used a silver century exhaust as a repair. Without doing as I suggested you won't be able to see if the water delivery tub...
by Charles uk
Sat Jun 01, 2019 9:08 am
Forum: Help
Topic: TC 102 water cooling problem
Replies: 23
Views: 961

Re: TC 102 water cooling problem

Isn't it connected into the exhaust?
by Charles uk
Fri May 31, 2019 7:38 pm
Forum: Help
Topic: TC 102 water cooling problem
Replies: 23
Views: 961

Re: TC 102 water cooling problem

If you get no joy after trying Nudge's suggestion, take it out of the water, remove the bottom end of the water into the exhaust tube from the top of the water into the exhaust/tell tale fitting & attach it into the end of your garden hose after checking the olive doesn't come off. Now back flus...

Go to advanced search