Search found 115 matches
- Fri Nov 11, 2016 10:04 am
- Forum: Help
- Topic: TC 102 exhaust tube
- Replies: 20
- Views: 24636
Re: TC 102 exhaust tube
Yes the drive shaft is in the correct position top and at the bottom where it meets the pump housing. As a trial, I replaced the tube loosely without the internal water tube, and without the lower half of the gearbox, so there would be nothing to stop the tube from reaching full position except the ...
- Thu Nov 10, 2016 6:08 pm
- Forum: Help
- Topic: TC 102 exhaust tube
- Replies: 20
- Views: 24636
TC 102 exhaust tube
Yes, its me again. Got a problem with my exhaust tube. on reassembly, with everything in the correct position I now find the exhaust tube appears to be too short. Never noticed this before. Even allowing for the water tube to bend out and away from the bottom there is as much as 15mm left uncovered ...
- Wed Nov 09, 2016 9:25 am
- Forum: Help
- Topic: cylinder tolerences
- Replies: 11
- Views: 14412
Re: cylinder tolerences
As you say, not much difference between the 2 carbs; after a bit of a search on the net I found that most of the part nos. are the same. However, my 2 jet seems to be ok on the threads, so I think maybe I am lucky.
- Sun Nov 06, 2016 4:03 pm
- Forum: Help
- Topic: cylinder tolerences
- Replies: 11
- Views: 14412
Re: cylinder tolerences
Thanks " Charles UK " for your advice , I will have a go. As far as the carb is concerned ; I will find the answer and let you know! All power to Brits! ( engines)
- Sun Nov 06, 2016 10:13 am
- Forum: Help
- Topic: cylinder tolerences
- Replies: 11
- Views: 14412
Re: cylinder tolerences
I posted the last reply before I saw the other info regarding measuring the piston ring gap. Thanks to you all for your help!
PS. Is the 2 jet carb as used on the TC 102 the same carb as the 46n 3A ? they look similar. ?
PS. Is the 2 jet carb as used on the TC 102 the same carb as the 46n 3A ? they look similar. ?
- Sun Nov 06, 2016 10:07 am
- Forum: Help
- Topic: cylinder tolerences
- Replies: 11
- Views: 14412
Re: cylinder tolerences
I am using a vernier caliper, which of course only measures a short way up from the bottom of the bore; so I adapted a pair of dividers , inserted them ( repeatedly) and then measured them with the vernier. Not ideal, but I got a fairly consistent 2.236/7 " reading. Interestingly there were a f...
- Fri Nov 04, 2016 10:52 pm
- Forum: Help
- Topic: cylinder tolerences
- Replies: 11
- Views: 14412
Re: cylinder tolerences
thanks oyster, I think it must be good then. I bit of servicing and it will be good for next season ! cheers!
- Fri Nov 04, 2016 8:54 pm
- Forum: Help
- Topic: cylinder tolerences
- Replies: 11
- Views: 14412
cylinder tolerences
My my service manual for a Tc 102 shows a cylinder tolerance of 2.237/8 " yet when I measured it I made it 2.235". Am I reading this correctly? What is the manufactured size?.. Cheers!
- Wed Nov 02, 2016 9:34 am
- Forum: Help
- Topic: amal 2 jet
- Replies: 2
- Views: 5894
Re: amal 2 jet
Cheers Inspector!
- Tue Nov 01, 2016 10:50 am
- Forum: Help
- Topic: amal 2 jet
- Replies: 2
- Views: 5894
amal 2 jet
Hi, is there a picture of an amal 2 jet carb on the site I can look at? and is it the same as a 46 ne 3a ?cheers!