Marston OG rebuild

You can talk about almost anything here

Moderators: John@sos, charlesp, Charles uk, RickUK, Petergalileo

User avatar
Oyster 49
Posts: 3316
Joined: Tue Oct 26, 2010 6:55 pm
Location: Derbyshire, UK

Marston OG rebuild

Post by Oyster 49 »

I've had this engine for quite a while, but have finally got around to doing some work on it over the last 2 winters. So I'll show the work done bit by bit, and the issues found.

First job was to do a general clean and check over, followed by taking a close look at the transom bracket. It was mostly all there, but several seized up fasteners to deal with. It had a broken and seized screw in place, which came out with a little heat and gentle persuasion, followed by re-cutting the threads and fitting new screws, I had obtained replacement transom screws and pads from the Marston Register.

The corroded cross brace bar on the transom bracket was pretty nasty and corroded, so I made a new one out of stainless, which polished up close to the original chrome.

Then a general clean and scrub of the bracket body, before reassembling, all threads freed and threads chased, and greased.

More to follow...
Attachments
IMG_5139.JPEG
IMG_5180.JPEG
IMG_5145.JPEG
IMG_5142.JPEG
iCloud Photos (6).zip
(2.48 MiB) Downloaded 304 times
Last edited by Oyster 49 on Wed Nov 08, 2023 9:46 pm, edited 3 times in total.
User avatar
Oyster 49
Posts: 3316
Joined: Tue Oct 26, 2010 6:55 pm
Location: Derbyshire, UK

Re: Marston OG rebuild

Post by Oyster 49 »

Finished bracket, cleaned, repaired and new parts fitted. Now 100% serviceable and functional.
Attachments
IMG_5148.JPEG
IMG_5183.JPEG
IMG_5149.JPEG
User avatar
Collector Inspector
Posts: 4195
Joined: Sun Jun 29, 2008 4:32 am
Location: Perth Western Australia
Contact:

Re: Marston OG rebuild

Post by Collector Inspector »

I am going to learn about these aye. Following with interest

B
A chicken is one egg's way of becoming others
User avatar
Oyster 49
Posts: 3316
Joined: Tue Oct 26, 2010 6:55 pm
Location: Derbyshire, UK

Re: Marston OG rebuild

Post by Oyster 49 »

Next job after sorting out the transom bracket was to restore the rusty cylinder. A good degrease using washing up liquid and hot water, followed by a flush of the waterways.

To paint, prepare using a wire brush and rubbed down with emery paper. Then a coat of kurust to treat the corrosion, then a coat of etch primer, then 2 coats of VHT paint. Finally an hour on top of the log burner to cure the paint. A big improvement.
Attachments
IMG_5176.JPEG
IMG_5141.JPEG
IMG_5103.JPEG
IMG_5088.JPEG
IMG_5086.JPEG
User avatar
Oyster 49
Posts: 3316
Joined: Tue Oct 26, 2010 6:55 pm
Location: Derbyshire, UK

Re: Marston OG rebuild

Post by Oyster 49 »

Next job was to strip and examine the carb, which was missing the small brass shaft that connects the carb to the gear linkage. With this model when you put the engine into gear, it automatically opens the throttle to whatever the throttle lever is set to. Drop it into neutral and the engine drops to tickover, set via the tickover screw on the carb. Clever 8) This is why this model has a cutout button on the tiller.
Attachments
IMG_3784.jpeg
User avatar
Collector Inspector
Posts: 4195
Joined: Sun Jun 29, 2008 4:32 am
Location: Perth Western Australia
Contact:

Re: Marston OG rebuild

Post by Collector Inspector »

How cool is that then.

B
A chicken is one egg's way of becoming others
User avatar
Oyster 49
Posts: 3316
Joined: Tue Oct 26, 2010 6:55 pm
Location: Derbyshire, UK

Re: Marston OG rebuild

Post by Oyster 49 »

Yes, simple but clever. They did away with the FNR engines when they decided the reverse gear was rarely used and not needed and could save money. What a shame! The carb has a drain valve which is a great feature also.
User avatar
Collector Inspector
Posts: 4195
Joined: Sun Jun 29, 2008 4:32 am
Location: Perth Western Australia
Contact:

Re: Marston OG rebuild

Post by Collector Inspector »

That little thing.....drain tap?

What a wonderful addition.

0A262 has one.

By the way I still need either a 0.020 over piston for the block...OR a standard 50mm block?

Over many years nobody wants to help me with a 50mm block? Is this such a special club?

The 0.020 block I have is otherwise pristine by the way.

Get me a standard barrel and everything done and dusted...I can actually use it (OA262)

20231120_132531[1].jpg
Your project is proceeding nicely by the way.
[/color][/color][/color][/b]
B
A chicken is one egg's way of becoming others
User avatar
Oyster 49
Posts: 3316
Joined: Tue Oct 26, 2010 6:55 pm
Location: Derbyshire, UK

Re: Marston OG rebuild

Post by Oyster 49 »

Can you get oversize pistons? I don’t recall ever seeing oversize blocks or pistons for any seagull? Could you look at Villiers engines from the 1930s that might have used a similar piston, perhaps with a bit of machining to make it fit?
User avatar
Charles uk
Posts: 4961
Joined: Wed Feb 27, 2008 4:38 pm
Location: Maidenhead Berks UK

Re: Marston OG rebuild

Post by Charles uk »

Bruce, we can list your standard size cylinder on the Marston Wish List should you require one, hate to think what one will cost.
This is the least common of all the Marston cylinders.

As I've never heard any mention of a 50mm 20 oversize piston with ring gaps suitable for a series one OA
Make it idiot proof and someone will make a better idiot.
User avatar
Collector Inspector
Posts: 4195
Joined: Sun Jun 29, 2008 4:32 am
Location: Perth Western Australia
Contact:

Re: Marston OG rebuild

Post by Collector Inspector »

Thanks guys.

My block is 20 over.....the piston is standard 50mm....have no idea why.

Charles. Remember the block I sent you?

Wish I still had it aye.

Back to the 0G now. Not diverting this topic any more. I will reopen my initial wanted.

B
A chicken is one egg's way of becoming others
User avatar
Oyster 49
Posts: 3316
Joined: Tue Oct 26, 2010 6:55 pm
Location: Derbyshire, UK

Re: Marston OG rebuild

Post by Oyster 49 »

A new piston could be made from solid bar of course.
User avatar
Oyster 49
Posts: 3316
Joined: Tue Oct 26, 2010 6:55 pm
Location: Derbyshire, UK

Re: Marston OG rebuild

Post by Oyster 49 »

Next job was to strip the magneto, all fairly routine as its the same as later engines. The coil was of course dead, but new ones are available. Its always a good idea to apply a little heat, as a steel thread in an alloy casting will most like be seized. I even have a tiny torch with runs on lighter fuel, similar size to a big cigar 8)
Attachments
IMG_3780.JPEG
IMG_3779.JPEG
IMG_3776.JPEG
IMG_3772.JPEG
User avatar
Oyster 49
Posts: 3316
Joined: Tue Oct 26, 2010 6:55 pm
Location: Derbyshire, UK

Re: Marston OG rebuild

Post by Oyster 49 »

Next job was to investigate the gearbox, and would the end cap come off? I was hopeful as the FNR gearbox does not have the water pump behind the cap, so less chance of deep corrosion in the threads. Eureka!, it came off easily :D A full degrease and clean, and generally all in very good condition.
Attachments
IMG_3795.JPEG
User avatar
Oyster 49
Posts: 3316
Joined: Tue Oct 26, 2010 6:55 pm
Location: Derbyshire, UK

Re: Marston OG rebuild

Post by Oyster 49 »

Next job was to give the crankcases a bit of a clean, and replace the tiller stub which had sheared. The original was made from monel, which is hard to find, luckily a brass SD one is identical. The treads in the crankcase for the tiller stub needed a light clean up by passing a tap through.
Attachments
IMG_5172 - Copy.JPEG
IMG_5116 - Copy.JPEG
IMG_5115 - Copy.JPEG
IMG_5175 - Copy.JPEG
Post Reply